2025.01.21
○Ver2025.01210
▲ additional functions
- Supports Kashifuji hobbing machines in the hobbing machine processing condition DB
- Added coordinate data to alarm history
- Added remote support launch from Viewer
- Fixed collected data of arc cumulative time of welding robot
- Adjusted adding measurement end condition of high sampling function
▼ bug fixes
- Fixed display error of part number/product name/process name in PLC data
- Fixed gain setting error when taking pictures inside the machine
2025.01.07
○Ver2025.01070
▲ additional functions
- Added measurement end condition of high sampling function
- Added registration function for equipment not connected to KOM-MICS
▼ bug fixes
- Fixed delay in reflection of tool reset information
2024.12.17
○Ver2024.12170
▼ bug fixes
- Fixed a bug in torque characteristic settings
2024.12.12
○Ver2024.12120
▲ additional functions
- Improved finishing cutting edge temperature in hob processing condition DB
- Improved automatic update of Logger software for in-machine photography
2024.12.05
○Ver2024.12050
▲ additional functions
- Added calculation of improvement potential for chip breaking control
- Added unused tool extraction function
▼ bug fixes
- Fixed a bug when exposure time was set to auto in the in-machine photography function
- Fixed a bug in tool improvement potential calculation
- Fixed a bug in which notifications were not displayed when UWF was disabled
- Fixed a bug when registering two cameras in the in-machine photography function
2024.11.28
○Ver2024.11280
▲ additional functions
- Improved the method of searching for comments within a program/job
2024.11.21
○Ver2024.11210
▲ additional functions
- Added PLC data acquisition function for Mitsubishi (M700, M800, C70)
- Supports voltage settings up to 5,000V with power sensor
▼ bug fixes
- Fixed malfunction when clicking on version display
- Added malfunction of in-machine photography when equipment power is cut off
- Fixed malfunction of EnOcean signal lamp causing processing of other company’s products
2024.11.07
○Ver2024.11070
▲ additional functions
- Added potential for improving chatter suppression control
- Added program output function for chatter suppression control
- Added chatter suppression program item to process completion history
- Supports acquisition of both spindle load and FANUC load torque
- Added “no filtering” to abnormality detection AI operating status
- Added PLC alarm acquisition function (via OPC server)
▼ bug fixes
- Fixed bug in signal light measurement screen
2024.10.30
○Ver2024.10300
▼ bug fixes
- Fixed the automatic update bug for remote control/in-machine photography
2024.10.29
○Ver2024.10290
▲ additional functions
- Fixed the ServoViewer automatic startup bug for certain models of terminals
- Added product name display to welding robot time chart
- Added camera IP address setting for remote control/in-machine photography
- Fixed Mitsubishi CNC macro variable changes for remote control/in-machine photography
- Improved work order prediction function
▼ bug fixes
- Fixed the bug where equipment management indicators were not recorded in process data
2024.10.22
○Ver2024.10220
▲ additional functions
- Improved program evaluation function
- Improved in-flight shooting history
- Added simplified installation of remote control and in-flight shooting functions
▼ bug fixes
- Fixed issue when clicking on the menu for UWF enable/disable function
- Fixed installation issue for Windows 11
2024.10.17
○Ver2024.10170
▲ additional functions
- Added UWF enable/disable function
- Added automatic installation of ServoViewer
- Added user control function for equipment types
▼ bug fixes
- Fixed issue with AI abnormality output for high sampling period measurement
- Fixed issue with security key input for Wi-Fi settings
2024.10.08
○Ver2024.10080
▲ additional functions
- Improved data acquisition in the hobbing machine processing conditions database
- Added SAR enablement to equipment registration information
2024.10.01
○Ver2024.10010
▲ additional functions
- Supports acquisition of 8-digit FANUC program numbers
- Improved NC program acquisition function for DMG-MORI CELOS
- Supports subprogram specification for high-speed sampling
- Added comment process completion judgment (supports equipment where @ cannot be entered)
- Supports receiving EnOcean repeater data
- Added constant log output for high-speed sampling measurement
2024.09.20
○Ver2024.09200
▲ additional functions
- Added management index function for PowerBI (creation/history)
2024.09.11
○Ver2024.09110
▲ additional functions
- Added support for high-speed sampling ammeter
▼ bug fixes
- Fixed a bug in channel delay calculation for high speed sampling
2024.09.05
○Ver2024.09050
▲ additional functions
- Added high-speed sampling measurement function
- Added European support for EnOcean power sensor
▼ bug fixes
- Fixed a bug in Wi-Fi setting process at first launch
2024.08.27
○Ver2024.08270
▲ additional functions
- Added power consumption to “Stop” history
- Split net work power consumption in “Process end” history by machining operation
- Supports notification of all alarms when multiple alarms occur
2024.08.20
○Ver2024.08200
▲ additional functions
- Supports acquisition of equipment MAC addresses for welding and non-FANUC machining
- Supports sensors aggregated in PLC (CSV linkage of external sensors)
2024.08.06
○Ver2024.08060
▲ additional functions
- Added PLC process-by-process recording function (simple recording mode)
▼ bug fixes
- Fixed bug that occurred duplicates in alarm history
2024.07.30
○Ver2024.07300
▲ additional functions
- Added tool life acquisition function for JTEKT equipment
- Added delay message for Okuma OSP
- Supports swinging around LoggerManager terminals
- Added count-up button to work ID input
▼ bug fixes
- Fixed bug in Wi-Fi setting process at first launch
- Fixed installer bug for in-machine photography function
2024.07.18
○Ver2024.07180
▲ additional functions
- Added a process to save the KOM-MICS Logger+.param update log
- Added a process to count the number of times chip cutting is applied
- Partially improved Wi-Fi setting process at first startup
- Improved the welding robot backup process
▼ bug fixes
- Fixed a bug when selecting tool number in remote control function
2024.06.28
○Ver2024.06280
▲ additional functions
- Improved model generation for work order instruction function
- Added remote control/in-flight photo confirmation function
▼ bug fixes
- Fixed a bug in comparing command program change history
2024.06.21
○Ver2024.06210
▲ additional functions
- Supports Wi-Fi settings on first launch
2024.06.20
○Ver2024.06200
▲ additional functions
- Added FANUC handling robot data acquisition function
- Added hobbing machine machining condition calculation function
2024.06.18
○Ver2024.06180
▲ additional functions
- Added AirGrid LAN communication disconnection detection function
2024.06.04
○Ver2024.06040
▲ additional functions
- Sum of breakdown power consumption improved to total power consumption.
▼ bug fixes
- Fixed a bug in obtaining OMRON road meter
2024.05.21
○Ver2024.05210
▼ bug fixes
- Fixed a bug in polling communication to the server.
- Fixed a bug in the OMRON controller file in the installer.
- Fixed a problem in calculating stop factors in the program evaluation function (machining)
2024.05.14
○Ver2024.05140
▲ additional functions
- Added installer file unblocking process
2024.05.09
○Ver2024.05090
▲ additional functions
- Support for macro variable linkage in tool life monitor
- Support for FFT range calculation during normal processing when acquiring FFT data
- Changed the sensor settings for KELGEN cooperation to the KELGEN sensor model.
- Changed the evaluation/items of the program evaluation function (welding robot)
2024.04.09
○Ver2024.04090
▲ additional functions
- Changed to hide the proxy setting confirmation when starting for the first time
2024.04.04
○Ver2024.04040
▲ additional functions
- Automatically set T-code tool change on lathes other than FANUC30i
- Program evaluation function (welding robot) evaluation/addition of items
2024.03.26
○Ver2024.03260
▲ additional functions
- Added automatic acquisition of IP address for edge terminals
- Change of alarm acquisition method in PLC/CSV mode
2024.03.21
○Ver2024.03210
▲ additional functions
- Added a setting function for improvement study results
- Addition of Proxy setting function
- Addition of edge terminal remote control function
▼ bug fixes
- Fixed a bug where the internet goes OFFLINE when the internet connection is unstable.
- Fixed a problem with the CSV save destination for human visualization.
2024.03.14
○Ver2024.03140
▲ additional functions
- Added setting function for improvement study results
- Improved sensor data acquisition interval for KELK device cooperation
▼ bug fixes
- Fixed a bug when the maximum/average abnormality level of abnormal detection AI history was -1.
- Fixed an issue where the screen would go OFFLINE even when connected to the internet.
2024.03.07
○Ver2024.03070
▲ additional functions
- Addition of equipment abnormality alarm extraction function
- Added material-free calculation to the cut chips into pieces function
▼ bug fixes
- Fixed a bug when acquiring feed speed at DMG Mori Seiki Mitsubishi
2024.02.29
○Ver2024.02290
▲ additional functions
- Change in the method for calculating the amount of cut chips into pieces
- Exclude pre-processing fast forwarding for abnormal detection AI learning/inference
▼ bug fixes
- Fixed a bug when torque was not converted in cutting force calculation.
- Fixed a bug where a lot of abnormal detection AI history was output.
2024.02.27
○Ver2024.02270
▲ additional functions
- Change work ID to be retained until process completion in PLC mode
▼ bug fixes
- Fixed a bug that automatically closed on the work ID input screen.
- Fixed the normalization problem of abnormal detection AI
2024.02.15
○Ver2024.02150
▲ additional functions
- Addition of chip emission calculation function
- Improved the evaluation contents/items of the program evaluation function (welding robot)
- Compatible with abnormal detection AI in FFT data
- Response to robot side voltage problem in welding robot power estimation function
2024.02.01
○Ver2024.02010
▲ additional functions
- Add machining with program evaluation function
▼ bug fixes
- Fixed a program update problem at DMG-Moriseiki Lathe NC Mitsubishi
- Fixed a bug in recording each process with CSV linkage
2024.01.25
○Ver2024.01250
▲ additional functions
- Improved the operation status of Mazak controller
2024.01.16
○Ver2024.01160
▲ additional functions
- Added cutting force distance integral value to cutting force integral
2024.01.11
○Ver2024.01110
▲ additional functions
- Added spindle load (PMC) to FANUC cutting force calculation source
- Added tool change judgment in specific subprograms
- Compatible with torque diagrams for tool rotation axes/workpiece rotation axes other than FANUC
- Compatible with Okuma OSP process completion macro
- Supports automatic restart of human visualization software
- Added KELK device cooperation
- Added average anomaly degree with AI anomaly detection
- Optimized data writing process to the server
- Support for Windows Communication Foundation redirection function
- Improved equipment operation judgment using EnOcean power
- Change data acquisition flag to inverted using anomaly detection AI
- Compatible with EnOcean’s PM sensor
▼ bug fixes
- Fixed a problem where the welding robot was judged to be a third-party product.
2023.12.21
○Ver2023.12210
▲ additional functions
- Added comments for Abnomaly detection AI (equipment failure diagnosis)
- Added Andon remaining machining time estimation function
- Delete detailed data acquisition function
▼ bug fixes
- Fixed a bug in counting the number of chip breaks.
- Fixed a bug in obtaining the FANUC minimum unit.
2023.12.08
○Ver2023.12080
▲ additional functions
- Added measures for low-spec terminals in the “Cut chips into pieces” app
- Change the feed rate calculation method of DMG Mori-Seiki Mitsubishi
2023.12.05
○Ver2023.12050
▲ additional functions
- Addition of automatic amplitude adjustment function for cut chips into pieces
▼ bug fixes
- Fixed a bug in AI abnormality detection iPhone tool number notification
2023.12.01
○Ver2023.12010
▲ additional functions
- Added usage count/type/version acquisition for cut chips into pieces
- Added acquisition of FANUC command multiply value
- Improved data retention for human visualization
▼ bug fixes
- Fixed a bug when resetting of tool life by OSP
- Fixed a bug where the planned stop of the welding robot was not notified
- Fixed a problem in acquiring the operation panel history of the FANUC30i series
- Fixed a bug in determining the number of MAZAK parts
- Fixed a bug in obtaining the FANUC minimum unit
- Fixed a bug when acquiring JOB of Welding Logger
2023.11.14
○Ver2023.11140
▲ additional functions
- Corresponds to H number in tool number of FANUC tool list
▼ bug fixes
- Fixed a bug where planned stoppage of welding robot was not notified.
- Fixed a bug where the controller operation history became unclear during processing.
2023.11.09
○Ver2023.11090
▲ additional functions
- Added AIRGRID barcode function/volume function
- Support for embedding Brother controller DLL
▼ bug fixes
- Fixed a bug in the FANUC tool life macro acquisition function.
- Fixed a bug in the FANUC30i series of operation panel operation history.
2023.10.26
○Ver2023.10260
▲ additional functions
- Added macro variable change to process completion judgment in OSP
- Corresponding to the increase in data acquired by welding robots
- Improved the judgment of othor company’s products during welding robot processing
- Added automatic work interruption judgment for IoT positioner
- Supports automatic update when starting with administrator privileges
2023.10.17
○Ver2023.10170
▲ additional functions
- Suppression of PC lock when connected to FANUC custom macro enabled equipment
▼ bug fixes
- Fixed a bug in the communication amount confirmation function
2023.10.12
○Ver2023.10120
▲ additional functions
- Added process completion judgment based on the number of machining parts for MAZAK
- Compatible with MAZAK multi-tasking machines
- Added MAZAK machine file backup function
- Compatible with the increase in data acquired by welding robots
▼ bug fixes
- Fixed a bug in the abnormal detection AI judgment result.
- Fixed a bug when reloading the learning result file with abnormal detection AI
2023.10.03
○Ver2023.10030
▲ additional functions
- Addition of abnormal detection option confirmation function
- Change of backup execution conditions of FANUC Controller
- Addition of communication amount confirmation function
- Changing the drive where human visualization is saved
- Added data acquisition flag with abnormal detection AI
▼ bug fixes
- Fixed a bug where MAZAK would always show stop
2023.09.21
○Ver2023.09210
▲ additional functions
- Changed default values of voltage/power factor of wattmeter
- Support for AIRGrid LAN connection (WDR-PRO method)
▼ bug fixes
- Fixed a bug when editing tool life in tool editing
2023.09.12
○Ver2023.09120
▲ additional functions
- Added process completion judgment based on comments
- Changed the number of equipment registration in PLC/CSV mode to 150
- Changed the number of data acquired in PLC/CSV mode to 300.
- Support for AIRGrid LAN connection (WDR method)
- Added license notation for human visualization
▼ bug fixes
- Fixed a bug where a large number of blade edge change histories were registered when resetting.
2023.09.05
○Ver2023.09050
▲ additional functions
- Licensing support for human visualization
- Added abnormal detection AI load option confirmation function
- Addition of XML backup function for Mazak controller
- Changed the applicability of OSP tool life cooperation function to selection method
2023.08.25
○Ver2023.08250
▼ bug fixes
- Fixed a server communication bug in the logging process thread.
- Fixed a bug that occurred when the data of abnormal detection AI inference was delayed
2023.08.24
○Ver2023.08240
▲ additional functions
-Addition of program evaluation function
-Added processing to acquire tool life from macro variables
▼ bug fixes
- Fixed a negative bug in aggregated data PC power off time
2023.08.10
○Ver2023.08100
▲ additional functions
-Improvement of PAD swing function when connecting LAN cable
2023.07.25
○Ver2023.07250
▲ additional functions
- Addition of improvement potential transition app
- Added a function that requires OSP controller machine number input
- Added connection delay processing in the OSP controller
▼ bug fixes
- Fixed the display bug of the PC removal setting equipment of the existing equipment selection
2023.07.20
○Ver2023.07200
▲ additional functions
- Improved PMC data acquisition (Bit data acquisition)
▼ bug fixes
- Fixed a bug that the Logger version of the machinery information was not updated
2023.07.11
○Ver2023.07110
▲ additional functions
- Added complementary processing when the part number and process name in the processing condition history are blank
- Addition of custom macro confirmation processing in the chip division program
2023.07.04
○Ver2023.07040
▼ bug fixes
- Fixed an inference bug due to the line feed code of the anomaly detection AI
- Fixed an unnecessary restart bug in the system settings
- Fixed a bug in the inspection list screen display for periodic inspections
2023.06.29
○Ver2023.06290
▲ additional functions
- Added processing to acquire turning axis load meter
- Added support for damaged tool files.
- Added size adjustment of Logger setting screen (supports low monitor resolution)
- Addition of countermeasures against data delays in Brother equipment’s anomaly detection AI
- Added proxy authentication support for in-house apps
▼ bug fixes
- Fixed a bug that the terms of use were closed after being displayed
2023.06.22
○Ver2023.06220
▲ additional functions
- Added 10,000 tool registration function for tools
- Set the Windows restart setting to ON when setting for the first time
- Add license notation
- Added acceleration data acquisition function (using AD unit)
- Addition of execution judgment of Windows Update automatic execution
- Added processing to change tools in a specific subprogram
2023.06.15
○Ver2023.06150
▲ additional functions
- Added the process end in the program operation state on the OSP lathe
▼ bug fixes
- Fixed a bug that also works with ATC/APC of anomaly detection AI
- Fixed an inference bug due to the line feed code of the anomaly detection AI
- Fixed APCor auto-restart setting bug for process completion judgment
2023.06.01
○Ver2023.06010
▲ additional functions
- Supports tool change by a specific subprogram
- Addition of splash window
▼ bug fixes
- Fixed TOSNUC program loading bug
2023.05.30
○Ver2023.05300
▲ additional functions
- Improvements to Eventhub’s production volume count
- Change the length of the human visualization video (15 minutes/video)
- Compatible with laser power measurement values of laser processing machines
- Improved transmission processing related to Logger history
- Added a function to enable network search for human visualization
- Added shared folder setting function for human visualization
- Addition of camera image processing function for work result collection function
- Param file quadruple support
▼ bug fixes
- Fixed a defect in equipment failure diagnosis target determination in anomaly detection AI
2023.05.19
○Ver2023.05190
▲ additional functions
- Improved processing of the power estimation function by machining process
▼ bug fixes
- Fixed a bug in the calculation of cutting speed and cutting distance in the machining condition DB
2023.05.18
○Ver2023.05180
▲ additional functions
- Display the PCID of the person-visible terminal in the Machinery information
- Added 10,000 tool registration function for tools
- Added terms of use for human visualization function
▼ bug fixes
- Fixed a bug where the external LTE connection was subject to IP address change
2023.05.11
○Ver2023.05111
▲ additional functions
- Addition of regular maintenance app
▼ bug fixes
- Fixed a history bug when applying multiple AIs in one process with Abnormal detection AI
2023.05.09
○Ver2023.05090
▲ additional functions
- Improved modal G code search for machining condition DB/machining condition history
- Improved the equipment detail type for machining to be a mandatory selection
- Corresponding to the improvement potential of turning
- Added power estimation function for machining
- Compatible with Azure storage of created videos with the human visualization function
- Set the installation drive to the default D:
▼ bug fixes
- Fixed a bug where images were not displayed when selecting a web camera for people visualization
2023.04.25
○Ver2023.04250
▲ additional functions
- Addition of welding robot axis configuration acquisition function
- Improved learning/judgment mode that considers fast-forwarding of abnormal detection AI
▼ bug fixes
- Fixed a bug when resetting the state of the signal watcher
- Fixed a bug when storing names in Enocean data
2023.04.11
○Ver2023.04110
▲ additional functions
- Add modal G code acquisition
- Added acquisition of TOSNUC999 feed shaft torque
- Added automatic software update processing when equipment is not set
- Addition of automatic reset option for worker ID
▼ bug fixes
- Fixed a bug where the human visualization function videos were not saved
2023.04.06
○Ver2023.04060
▲ additional functions
- Addition of “cutting force tool life review” function
- Added support for Windows date and time differences
- Improved Windows Update operation by enabling/disabling UWF
- Improved “Cut chips into pieces” function
- Improved program acquisition processing in CELOS-FANUC
▼ bug fixes
- Fixed a bug that “Abnormal detection AI” function could not be applied in multiple systems
- Fixed a bug that prevented communication with the Mitsubishi controller C70
2023.03.28
○Ver2023.03280
▲ additional functions
- Exclude DONOTGET descriptions from backup in NC programs
- Added a function to display the W-axis coordinates in addition to the Z-axis coordinates
- Improved information acquisition processing for PC manufacturer and PC model
- Compatible with Brother equipment plug-ins
▼ bug fixes
- Fixed a bug where the same power continued for several minutes with an EnOcean power meter
- Fixed a bug that prevented communication with Mitsubishi C70 and C64 other than Mori Seiki
2023.03.17
○Ver2023.03170
▲ additional functions
- Addition of shank information input selection
- Improved achievement collection settings
- Add “.NET Framework 4.8” installation during installation
- Added processing to collect updates of command programs (NC, Job)
▼ bug fixes
- Fixed a bug that caused the human visualization function to fail to delete temporary files.
- Fixed a bug that automatically restarted Logger each time AI inference was enabled
- Fixed a bug that made AI inference impossible due to missing data when multiple systems were used.
2023.03.06
○Ver2023.03060
▲ additional functions
- LoggerManager supports mixed operation of different equipment types
- Added a function to monitor equipment machine
- Added a function to notify by e-mail when machine by network connection errors
▼ bug fixes
- Fixed program acquisition bug when update date error
- Fixed a bug that the processing number comment of the program was not reflected
2023.03.01
○Ver2023.03010
▲ additional functions
- Add support contact information display function
- Addition of insulation resistance data acquisition function
- Addition of temperature acquisition function for spindle and servomotor
- Improved the EXCEL output of the backup function.
▼ bug fixes
- Fixed a bug that the number of processed works@comment was not reflected.
2023.02.24
○Ver2023.02240
▲ additional functions
- Corresponds to the built-in Logger of the human visualization system
▼ bug fixes
- Fixed a bug where the weld weight of the welding robot was not calculated
2023.02.21
○Ver2023.02210
▲ additional functions
- Handover of time charts by existing equipment is supported at the initial setting
- Improved data sent to EventHub
- Added support when communication is not possible due to changes in macro variables for process completion judgment
- Compatible with Inaba sensors for EnOcean tricolor lights
- Added other software monitoring function by CSV/PLC mode Logger
2023.02.10
○Ver2023.02100
▲ additional functions
- LoggerManager supports mixed operation of different equipment types
▼ bug fixes
- Fixed a bug that the drawing of LoggerManager is not stopped
2023.01.27
○Ver2023.01270
▲ additional functions
- Added a function to automatically enter when the process is blank with the part number candidate function
- Added a function to notify the target program change of abnormal detection AI
- Add target AI name in abnormal detection AI non-application notification
▼ bug fixes
- Fixed a bug that welding robot operation is not reflected in time chart
2023.01.25
○Ver2023.01250
▲ additional functions
- Set Japanese IME to OFF when entering login input.
- Added a function to follow even when the name of the target program for abnormal detection AI is changed.
▼ bug fixes
- Fixed bugs in facility plug-in interface
2023.01.10
○Ver2023.01100
▲ additional functions
- Added automatic editing function for setting XML file of MAZAK controller
- Compatible with “OpenVino 2021.4.752” version of Abnormal Detection AI
▼ bug fixes
- Fixed a bug in the setting items of the MITSUBISHI controller.
- Fixed a bug where the UPDATE failure notification was not notified by manual restart.
- Fixed the problem that a completion message was displayed before completion when installing PLC mode.
2022.12.12
○Ver2022.12120
▲ additional functions
- Added a function to automatically follow changes in AI subject programs
- Added to learning target of Mitsubishi CNC’s Abnormal detection AI function
- Change automatic operation power threshold upper limit of power meter setting (1,000W→20kW)
2022.12.05
○Ver2022.12050
▲ additional functions
- Supports TMD feedrate
- Added CPU load reduction function for low-spec PCs
- Addition of Microsoft Edge linkage function
- Windows 11 support for openvino
2022.11.22
○Ver2022.11220
▲ additional functions
- Added input rule check button for tool list template
▼ bug fixes
- Fixed an operation bug when resetting tool life
2022.11.04
○Ver2022.11040
▼ bug fixes
- Fixed a bug that caused worker data was negative work time to be displayed
2022.10.31
○Ver2022.10310
▲ additional functions
- Added “Lathe” selection for equipment type in MAZAK CNC settings.
- Added a function to notify by e-mail in case of automatic update failure.
▼ bug fixes
- Fixed a bug that duplicate process data files were sent.
- Fixed a problem with Mitsubishi CNC other than DMG Mori-seiki.
2022.10.20
○Ver2022.10200
▲ additional functions
- A function to acquire spindle/feed axis motor power for FANUC30iB has been added.
- Program completion judgment “when the execution line of the main program decreases” is improved.
- Changed to display the password input of Wifi setting as it is.
- Support by adding equipment plug-in for DPRINT
2022.10.11
○Ver2022.10110
▲ additional functions
- Added PCID and sensor Ch value columns to equipment sensor list.
- Deleted DEX transmission function.
- Changed the method of acquiring equipment names in LoggerManager.
- Added a process for shifting to multiple systems in LoggerManager.
▼ bug fixes
- Fixed a bug that caused the work results collection function to be initialized after restarting the PC.
2022.10.04
○Ver2022.10040
▲ additional functions
- Added for MAPPS-MITSUBISHI G code judgment.
- Added link processing for WinCC-compatible alarm numbers and details.
▼ bug fixes
- Fixed line feed code bug when outputting program for Mitsubishi CNC.
2022.09.28
○Ver2022.09280
▲ additional functions
- Addition of automatic acquisition function for product name and material from NC program
- Addition of OSP lathe milling axis acquisition function
- Added PLC mode in install type to installer
- Added “Takebishi OPC-Server” linkage settings
- Added OPC-Server installer to install PLC mode
▼ bug fixes
- Fixed the work rotation speed calculation bug in the machining condition DB.
2022.09.20
○Ver2022.09200
▼ bug fixes
- Fixed a bug that the coordinate axis could not be taken with the OSP controller
2022.09.13
○Ver2022.09130
▲ additional functions
- Update the column items of the tool EXCEL template
- Added a function to use program-specific line comments as process information
- Added process start/end judgment method for IoT positioner
2022.09.09
○Ver2022.09090
▼ bug fixes
- Fixed a bug that the judged to be processing another company’s product in welding robot
- Fixed a bug where the process data of the welding robot could not be displayed
2022.09.07
○Ver2022.09070
▲ additional functions
- Add cutting force integral value to tool change judgment
▼ bug fixes
- Fixed a bug that made it impossible to operate on the terms of use screen
2022.09.01
○Ver2022.09010
▲ additional functions
- Supports changing the CSV folder of FFT data
- Display the tool radius compensation number and tool length compensation number on the measurement screen
- Reset all values to 0 when FFT data CSV has not been sent for 10 seconds
- Record the average value of any block when the CSV mode process is completed
2022.08.29
○Ver2022.08290
▼ bug fixes
- Fixed a bug that multiple alarms could not be acquired at the same time
- Fixed a bug in acquiring the automatic recognition of the product number
- Fixed a bug that caused “WEB access error” in the terms of use
2022.08.23
○Ver2022.08230
▲ additional functions
- Welding operation type added to welding robot
- Improvement of operation status judgment of welding robot
- Addition of FFT data import processing
▼ bug fixes
- Fixed an error that occurred when process end history overlapped
2022.08.05
○Ver2022.08050
▲ additional functions
- Compatible with spindle load meter of MITSUBISHI controller M80/M800
- Corresponds to data retention time of worker collaboration data
▼ bug fixes
- Fixed an automatic login setting bug in the registry
2022.08.01
○Ver2022.08010
▲ additional functions
- Deleted the job acquisition method item for welding robots (fixed to “Communication”)
- Added “In-House Apps” to the category
▼ bug fixes
- Fixed the worker data display bug of the time chart
2022.07.25
○Ver2022.07250
▼ bug fixes
- Correction of calculation bug of worker collaboration data
2022.07.21
○Ver2022.07210
▲ additional functions
- Added periodic processing of registry edit for Autologon setting.
- Added a QR reading check for the automatic work clothes collection function
- Improved the EventHub notification data of the automatic work clothes collection function
- Improved retry processing of FANUC Focas.
2022.07.15
○Ver2022.07150
▲ additional functions
- Supports individual Logger restart of Logger Manager
- Supports simplified initial login input for Logger Manager
▼ bug fixes
- Fixed a bug in network connection processing in Logger Manager
- Fixed a status problem when a server is abnormal in Logger Manager.
2022.07.08
○Ver2022.07120
▲ additional functions
- Addition of function for automatic collection of work start completion results
2022.07.08
○Ver2022.07080
▲ additional functions
- Supports acquisition of PG coordinate setting unit for “cutting force stabilized” function
- Added “Worker data linkage” column to “Machinery information” function
- Support for MITSUBISHI controller M80 / M800
- Adjusted the delay time of the data logging cycle
▼ bug fixes
- Fixed a bug that determines other company products when online is delayed
2022.06.30
○Ver2022.06300
▲ additional functions
- Added equipment power off judgment in CSV mode
- Addition of ”Worker data linkage” function
▼ bug fixes
- Fixed a bug that the cutting speed became “0” in the ”Cutting condition DB” function.
2022.06.01
○ Ver2022.06010
▲ additional functions
- Addition of detailed data acquisition function for equipment maintenance
2022.05.23
○ Ver2022.05230
▲ additional functions
- Added abandonment setting process to be executed when the installed equipment is abolished.
- Added welding robot predictive maintenance function
▼ bug fixes
- Fixed a problem in which EnOcean power from a cooperating company was displayed as the product of another company.
2022.05.16
○Ver2022.05160
▼ bug fixes
- Fixed a bug that the process end by welding robot communication cutting.
2022.04.26
○Ver2022.04260
▼ bug fixes
- Fixed a bug where edited machinery minor type were not applied.
2022.04.21
○Ver2022.04210
▼ bug fixes
- Fixed a bug that the same process was recorded more than once in the piece work.
- Fixed a bug in the cycle time calculation when the previous process was another company’s product.
2022.04.19
○Ver2022.04190
▼ bug fixes
- Fixed a bug that CPU load is high when OSP communication is not possible.
2022.04.18
○Ver2022.04180
▼ additional functions
- Added support for three systems of FANUC controllers.
2022.04.13
○Ver2022.04130
▼ additional functions
- Improved process completion judgment when line number decreases during main program execution
2022.04.08
○Ver2022.04080
▼ bug fixes
- Fixed a bug in the number of search cases for automatic acquisition of tool specs.
2022.04.01
○ Ver2022.04010
▼ additional functions
- Delete some input rules in the tool setup screen input and EXCEL file
(Tool model number 1 / Cutter head model number / Holder model number)
▼ bug fixes
- Fixed a bug in the approval flow with the DMG Moriseiki MAPPS controller.
2022.03.23
○ Ver2022.03230
▼ additional functions
- Added a timeout when acquiring the FANUC controller program.
- Added the license notation of the software used on the version screen.
- Added 32-bit C ++ 2012 runtime to the installer
- Improvement that enables setting and data acquisition by lineage each with multi-system machine tools.
▼ bug fixes
- Fixed a bug that tool life reset monitoring did not start.
2022.03.11
○ Ver2022.03110
▼ additional functions
- Create a shortcut for ”Start remote support” on the desktop
- Supports process data transmission restrictions and time chart data transmission priority
- Added “cumulative usage time [h]” to edge device management
▼ bug fixes
- Fixed a bug in detecting the program number and sequence number for process end judgment.
- Fixed a bug caused by continuous blank Enter key input on the logon input screen.
- Fixed a data acquisition bug for SIEMENS machine (WinCC) communication
- Fixed a bug in the data acquisition method of the welding robot
2022.03.01
○ Ver2022.03010
▼ additional functions
- Supports acquisition of data from other companies by general users with welding robots
- Changed the operation status judgment of the welding robot
▼ bug fixes
- Fixed a bug when saving the upper limit cutting feed rate
2022.02.15
○ Ver2022.02150
▼ additional functions
- Added the registration rate of detailed tool information to the “Machinery information” function.
- Changed to forcibly terminate related processes when reinstalling Logger
- Added processing to reduce the capacity of NC program files
- Corrected so that tool-related communication is not performed except for Machine processing.
- Added the process of restarting the EnOcean (three-color lamp / power meter, etc.) Logger software once a week.
▼ bug fixes
- Fixed a bug that the EnOcean communication process did not end.
2022.02.04
○Ver2022.02040
▼ additional functions
- Improvement of system setting items of Mitsubishi controller
- Added used tool list information to the tool edit screen
▼ bug fixes
- Fixed a bug that an empty IP address can be set in the Logger setting of the OSP controller.
- Fixed a bug in the block number of the main program of the OSP controller
- Fixed a bug related to process termination during automatic update
- Fixed a server communication problem with the Mitsubishi controller
- Fixed a bug in the version display in the Windows application list
- Fixed a bug that the KOM-MICS server status function does not work
2022.01.28
○Ver2022.01280
▼ additional functions
- Added the function to start Alive Monitor using the task scheduler
- Added work ID input function to welding logger
▼ bug fixes
- Fixed a bug in equipment manufacturer editing by maintenance software
2022.01.20
○Ver2022.01200
▼ additional functions
- Improved processing related to ”Robot base B” in Welding condition DB function
▼ bug fixes
- Fixed a bug in potential time aggregation with the air cut judgment function
2022.01.13
○Ver2022.01130
▼ additional functions
- Add equipment IP address / device IP address to “Machinery information” function
▼ bug fixes
- Fixed a bug that an error occurred when executing the installer
- Fixed display problems in environments other than 100% scaling of the installer
2022.01.11
○Ver2022.01110
▼ additional functions
- Supports invalidation of some M30 / N2 delimiters depending on the process end type
- Improved tool life acquisition of OSP controller
- Compatible with Logger Manager for machining (connects to multiple machining with one device)
- Add his robot base B [degree] / theoretical welding weight / theoretical leg length / heat input to “Welding condition DB”
- Supports automatic activation of barcode readers
- Added MELDAS parameter backup function
▼ Bug fix
- Fixed a bug in the temporary parts number function when the parts number comment is empty.
- Fixed a bug related to terminal information acquisition
- Fixed a bug that the initial setting cannot be done in Viewer when using Logger Manager.
- Fixed a bug due to stop processing at the end of Logger
2021.12.23
○Ver2021.12230
▼ bug fixes
- Fixed data acquisition bug of Siemens machine (WinCC) communication
2021.12.21
○Ver2021.12210
▼ bug fixes
- Fixed a bug that the server CPU becomes a high load
- Fixed a bug of no taking over the settings of edge device
- Fixed a bug that the product number and product name and process name is not reflected in the history function.
2021.12.15
○Ver2021.12150
▼ additional functions
– Added processing related to the sensor data function of KOM-MICS Viewer.
▼ bug fixes
– Fixed a loading problem of Mitsubishi controller DLL
(Addition of runtime library installation)
2021.12.08
○Ver2021.12080
▼ additional functions
– Added processing for receiving data from the sensor (EnOcean) and sending to the server.
– Added a notification function for abnormal stop of sensor (EnOcean) reception.
▼ bug fixes
– Fixed a bug related to the iPhone app advance notification function.
2021.12.02
○ Ver2021.12020
▼ additional functions
– Added processing to accumulate Logger operating time
– Added display of FTP account information in IIS settings for TOSNUC.
– Added the function to acquire macro variables in the FANUC controller.
▼ bug fixes
– Fixed the problem of frequent alarms on the OSP controller FMS line.
– Fixed a bug related to EnOcean support, (processing when communication is not received)
2021.11.18
○ Ver2021.11180
▼ additional functions
- Change the delay time when executing the communication return command
▼ bug fixes
- Fixed a bug related to EnOcean support (CPU high load, data clear processing)
2021.11.15
○ Ver2021.11150
▼ additional functions
- Added EnOcean support (signal tower / power meter, etc.)
▼ bug fixes
- Fixed a bug that the production count is not recorded in some of the process end types.
2021.11.12
○ Ver2021.11120
▼ additional functions
- Addition of equipment manufacturer “FANUC” selection with Mazak controller
- Changed the backup function of the OSP controller
- Changed the screen display in “DO NOT GET” mode
▼ bug fixes
- Fixed a bug related to communication confirmation of devices without screens
- Fixed a problem of deleting local program files in Mitsubishi CNC
2021.11.04
○ Ver2021.11040
▼ additional functions
- Added air cut judgment
- Stop displaying the “Production history” tab
▼ bug fixes
- Fixed a bug in Komatsu attribute write update operation.
- Fixed a bug that the alarm number of the TOSNUC controller is not displayed.
2021.10.28
○ Ver2021.10280
▼ bug fixes
- Fixed G-code discrimination operation bug in programs with more than 5,000 lines
- Fixed a bug that the time chart is not reflected in “CSV linkage” function
2021.10.25
○ Ver2021.10250
▼ additional functions
- Change of Server authentication method
- Added IIS automatic setting function for Tosnuc controller
- Addition of attribute comment “DO NOT GET” (Do Not Get Detail Data) mode
▼ bug fixes
- Changed the judgment process of the operating status at the end with the PC power off notification
- Fixed a bug that the server status function does not work
2021.10.14
○ Ver2021.10140
▼ bug fixes
- Fixed a bug during automatic software update
2021.10.11
○ Ver2021.10110
▼ additional functions
- Add an icon selecting the equipment type of the installer
▼ bug fixes
- Fixed the program acquisition error bug of FANUC-31i controller
2021.10.04
○ Ver2021.10040
▼ additional functions
- Corresponds to the case where there are two or more wired ports in the IP address setting
- Addition of “WiFi setting” function
- Addition of “Communication check” function
▼ bug fixes
- Fixed an automatic edge device ID generation bug
- Fixed a bug that process data is not complemented by CSV linkage
2021.09.24
○ Ver2021.09240
▼ bug fixes
- Fixed a bug when starting Tosnuc controller Logger
- Fixed a bug that the worker ID of the barcode reader is dropped by one character.
- Fixed a malfunction of login information when an authentication error occurs.
2021.09.22
○ Ver2021.09220
▼ additional functions
- Changed to automatically generate when the PC serial number is “Default string”
- Display the edge device ID and QR code on the setting waiting screen of Logger without screen
- Added data backup for Mitsubishi and Mazak CNC
▼ bug fixes
- Fixed a bug that caused high CPU usage of the Signal light Logger.
- Fixed the problem of hiding the application version in the maintenance software automatic return history.
- Added log output when the logging thread stops abnormally
2021.09.07
○ Ver2021.09070
▼ additional functions
- Added “0iD / 0iF” parameter “13104 # 1” warning display for FANUC controller
- Added WEB-API usage of Logger software to WEB-API usage history
- Added G code to ignore due to system settings on MAZAK controller
- Added a method for detecting process completion
▼ bug fixes
- Fixed a bug in displaying the main program name of general user equipment
- Fixed an error occurrence problem due to selection of existing equipment in the initial setting
- Deleted the input field “x” button on the system setting screen
- Fixed a bug that stopped during the automatic update process
2021.08.24
○Ver2021.08240
▼ additional functions
- Added automatic input of PC removal date and time with welding robot
- Added Siemens WinCC multi-axis support
- Added KOM-MICS Support Desk contact information to the menu screen
▼ bug fixes
- Fixed a bug that the menu screen was not displayed when server communication failed
2021.08.17
○Ver2021.08170
▼ additional functions
- Improved search process for product number candidates
- Improvement of cycle time analysis function
- Addition of option enable / disable setting of Logger monitoring function
- Improved the specifications of the cooperating company mode account of the “Machinery’s Data Sharing Settings” function
▼ bug fixes
- Fixed a bug in writing the operating PC name of “Machinery information” function
- Fixed a bug that caused a operation status to “Stop” during processing.
- Fixed a bug that the server status is not displayed
- Fixed the automatic recovery problem of TOSNUC equipment with the Logger monitoring function.
2021.08.03
○Ver2021.08030
▼ additional functions
- Improvement of Logger monitoring function (excluding change of return monitoring time and monitoring without UI response)
▼ bug fixes
-Fixed an automatic recovery problem of FANUC equipment with the Logger monitoring function.
-Fixed a bug that the PC name of the “Machinery information” function was blank.
2021.07.30
○Ver2021.07300
▼ additional functions
- Added “Equipment Disposal Datetime (UTC)” to “Machinery infomation” function
- Corresponds to product number comment “BANGOU”
▼ bug fixes
- Fixed a bug that automatic recovery occurs in OSP Controller
2021.07.26
○Ver2021.07260
▼ additional functions
- Improved the installer for screenless terminals
- Added Wi-Fi profile import application function
2021.07.16
○Ver2021.07160
▼ additional functions
- Addition of Logger monitoring and automatic recovery software
▼ bug fixes
- Fixed a bug in process information of operating status in OSP controller Machining tool
- Fixed a bug that the update process was not completed
- Fixed a bug that memory usage is excessive
2021.07.08
○ Ver2021.07080
▼ bug fixes
- Fixed a bug that the menu screen cannot be operated on some terminals
2021.07.05
○ Ver2021.07050
▼ bug fixes
- Fixed a drawing problem on the menu screen
2021.07.02
○Ver2021.07020
▼ additional functions
- Improved the calculation method of search speed ratio and current range used
- Added a function to display the server status when the server cannot be connected
▼ bug fixes
・Fixed auto login bug in Machining tool Logger
2021.06.28
○ Ver2021.06280
▼ additional functions
- Improvement of part number candidate acquisition function
- Supports Windows login users without administrator privileges
- Added the function to set the availability for each application for each account
- Change the priority of the Logger process
- The setting screen is displayed when the welding logger is started for the first time
▼ bug fixes
- Fixed a bug in Logger Manager task scheduler
- Fixed an installation problem with the OMRON controller
- Fixed a problem when equipment communication was not possible with FANUC tool cooperation
2021.06.16
○ Ver2021.06160
▼ additional functions
- Compatible with trademarks of each country (switching of “KOM-MICS” notation)
- Improved product number acquisition method
- Supports welding potential calculation (air cut, search, positive parallel)
▼ bug fixes
- Fixed a bug that occurred when the welding JOB program was long.
- Fixed a bug that the output csv data format for TurnGreen is different.
2021.06.09
○ Ver2021.06090
▼ additional functions
- Improved speed in CSV mode
▼ bug fixes
- Fixed a bug that LoggerManager cannot be operated.
2021.06.01
○ Ver2021.06010
▼ additional functions
- Link the tool management function of FANUC and the tool management function of KOM-MICS
▼ bug fixes
- Fixed a bug when an authentication error occurs on an edge device terminal
- Fixed a bug that data transmission stagnates in long-term processes
2021.05.24
○Ver2021.05240
▼ additional functions
- Added tool information to the machining condition DB
- Partially changed the operation screen of ”Tool setup” function.
- Added a cancel button to the progress display when acquiring the “Select Machinery” list.
- Improved OMRON controller DLL.
- Changed the logging interval for CSV linkage to a minimum of 50 msec.
▼ bug fixes
- FANUC only fixed X / Y / Z / A / B / C axis acquisition bug.
- Fixed a bug that Logger is ONLINE but Viewer is PC power off due to welding.
2021.05.13
○Ver2021.05130
▼ additional functions
- Changed the version notation to date format.
- Welding air cut ratio / search speed ratio / working current range / counter value added.
- Improvement of welding productivity monitor.
- Added the number of spindles / X / Y / Z / A / B / C / all axis names to the equipment registration information.
2021.05.10
○Ver3.53
▼ bug fixes
- Deleted log output processing when logging delay occurs.
2021.04.28
○Ver3.52
▼ additional functions
- Added search shift amount to welding process data.
2021.04.14
○Ver3.51
▼ additional functions
- Addition of cycle time analysis function.
▼ bug fixes
- Fixed a bug that tool information was not reflected when the default equipment was registered.
- Fixed to shorten the period when tool information does not match.
- Fixed a bug that the tool life monitor was not updated.
2021.04.08
○Ver3.50
▼ additional functions
- Removed the tool management function for gear cutting machines.
- Exclude unnecessary files from the installer.
2021.04.05
○Ver3.49
▼ bug fixes
- Deleted the process of acquiring the work origin offset value with the system variable.
2021.03.31
○Ver3.48
▼ additional functions
- Improvement of ATC event sending function.
- Added “New equipment registration (copy of existing equipment settings)” to the initial settings
- Added a function to evaluate equipment capacity from operating rate.
▼ bug fixes
- Changed not to display a message when registering equipment.
2021.03.25
○ Ver3.47
▼ additional functions
・ Added a setting setting wizard when the machining Logger is started for the first time.
▼ bug fixes
・ Fixed a network address confirmation problem in the system settings
・ Fixed a bug that the coordinate system of machine coordinates is not reflected normally.
2021.03.23
○ Ver3.46
▼ additional functions
・ KOM-MICS option introduction waiting screen design change
▼ bug fixes
・ Fixed a bug that the CPU load of the CSV linkage function is high.
2021.03.17
○ Ver3.45
▼ bug fixes
・ Reverted to the previous version due to a defect in the latest version of Remote support module.
・ Reverted to the previous version due to a DLL defect for the welding machine C4.
2021.03.15
○ Ver3.44
▼ additional functions
・ Changed the description at the time of installation.
・ Added “Approval” to the status of equipment manufacturer inquiries.
▼ bug fixes
・ Fixed a bug related to the CSV linkage function.
・ Fixed a bug that process completion cannot be obtained by process completion judgment “macro variable change”.
・ Fixed a bug that the system setting “Windows Update login setting” is always displayed.
・ Fixed a bug that the process name and part name of the welding machine could not be obtained.
2021.03.09
○ Ver3.43
▼ additional functions
・ Added CSV linkage function.
2021.03.05
○ Ver3.42
▼ additional functions
・ Added acquisition of equipment information “series number” and “MODEL information”
2021.03.01
○ Ver3.41
▼ additional functions
・ Added “Loading” display during server communication on the WEB display
・ Improved the operating speed of the equipment controller selection page in the system settings
・ Updated the welding machine job DLL to the laser welding machine compatible version
▼ bug fixes
・ Fixed a bug on the screen waiting for the option introduction of the device without screen
2021.02.16
○ Ver3.40
▼ additional functions
・ Change the priority of welding robot operating status judgment (error stop, planned stop)
・ Added Windows Update button to the top menu screen
2021.02.10
○ Ver3.39
▼ bug fixes
・ Fixed a bug in saving equipment settings other than FANUC on the initial setting screen
・ Corrected the item name in English mode
2021.02.09
○ Ver3.38
▼ additional functions
・ Supports operation with the latest version of TeamViewer.
・ Change “M2 / M30” to selectable when the system setting “Process end”
・ TLS1.2 compatible
2021.01.27
○ Ver3.37
▼ additional functions
・ Added process completion judgment based on the total number of machined parts when the FANUC option is enabled
・ Added equipment manufacturer / controller GUI selection to Logger settings
・ Added DLL download process for DMG Mori Seiki MAPPSV
・ Added KOM-MICS option introduction waiting screen
2021.01.18
〇Ver3.36
▼ additional functions
・First time setting and system setting are standardized to WebUI.
・Added “Machine number” and the item related to the equipment manufacturer to the system setting.
・Excluded the DLL related to MAPPSV of DMG Mori Seiki from the installer.
2021.01.13
〇Ver3.35
▼ additional functions
・OMRON controller DLL was added.
▼ bug fixes
・The backup function at the time of the setting file damage is corrected.
・Logger immediate termination processing at the time of UWF execution user was added in Windows Update function.
2020.12.22
〇Ver3.34
▼ additional functions
・Added a function to automatically calculate the drill L/D used in the improvement potential.
2020.12.18
〇Ver3.33
▼ additional functions
・.NET Framework to be installed was changed to 4.6.2.
・Added tool life setting values for tools.
・Changed to support part number format setting.
・Changed the IP address setting of the MAZAK controller.
・Changed service start folder of MAZAK controller.
2020.12.15
〇Ver3.32
▼ additional functions
・Changed the display source URL for the update history function.
・Support for Windows Update on edge device terminals.
・Improved update distribution function.
・Added radius command/diameter command to process data.
▼ bug fixes
・Fixed a bug that weekly aggregation was not executed in the utilization rate aggregation function.
2020.12.10
〇Ver3.31
▼ additional functions
・Support for welding machine of edge device terminal
2020.12.07
〇Ver3.30
▼ bug fixes
・Added the backup function when the setting file is damaged.
・Fixed a bug that an error occurs after consent when LoggerManager is started for the first time.
2020.12.02
〇Ver3.29
▼ additional functions
・Improved the judgment of process name pause.
・TELNET automatic setting for MAZAK controller was added.
・Support for laser welding machines.
・G code judgment method of MAZAK controller was changed.
・Addition and improvement of the IoT positioner function.
2020.11.27
〇Ver3.28
▼ additional functions
・Add color to the function icons.
▼ bug fixes
・Fixed a bug that prevented Weld Logger from starting.
2020.11.24
〇Ver3.27
▼ additional functions
・Support for models where “@” cannot be used in program comments.
・Added upper limit spindle speed and upper cutting feed rate to the ”Cutting information” function.
・Support for Tchmore built-in KOM-MICS.
・Changed the display name of the elevation axis of the IoT positioner.
・Changed the handling of IoT positioner emergency stop.
・Added the number of remaining tools in the tool life monitor (e.g., time, etc.) and update date.
・Respond to a large number of alarms generated by operator messages.
2020.11.13
〇Ver3.26
▼ additional functions
・Added AD value (value after unit conversion) display for IoT positioners.
・Added Internet connection type and edge device OS to “Machinery information” function.
・Changed the reset decision for “Cutting Tips change” history function in conjunction with OSP facilities.
▼ bug fixes
・Fixed a Logger crash when the Mitsubishi MELDAS driver does not exist.
・Fixed a bug that the button is not released during emergency stop of IoT positioner.
2020.11.05
○ Ver3.25
▼ additional functions
・Added “Estimated Workpiece Size” to the Process Completion History.
2020.11.04
○ Ver3.24
▼ additional functions
・Changed to use G54 offset amount for the same value with or without tool length in absolute coordinates.
2020.10.30
○ Ver3.23
▼ additional functions
・Compatible with unit inches.
2020.10.28
○ Ver3.22
▼ additional functions
・Welding IoT positioner/SAW-related functions (e.g., Tchmore integration)
・The color of the operating status display is consistent
2020.10.23
○ Ver3.21
▼ additional functions
・Welding IoT positioner/SAW support
2020.10.15
○ Ver3.20
▼ additional functions
・ Added processing to enable from disabling Wi-Fi
・ Changed to try reconnection at all connection destinations that are valid when Wi-Fi is disconnected
2020.10.09
○ Ver3.19
▼ additional functions
・ Improvement of 3D model display of parts in 3D display of machining toolpath
▼ bug fixes
・ Correction of error display contents when importing tools
2020.09.29
○Ver3.18
▼ additional functions
・Supports multiple display of errors when importing tool data.
▼ bug fixes
・Fixed a bug in tool replacement data when linking with OSP tool life management.
2020.09.28
○Ver3.17
▼ additional functions
・Corresponded to A-axis and C-axis of FANUC and OSP controller.
・Added FANUC parameter to equipment registration information.
▼ bug fixes
・Fixed a bug that the terms of use could not be displayed.
2020.09.24
○Ver3.16
▼ additional functions
・Improved the display method of terms of use.
2020.09.18
○Ver3.15
▼ additional functions
・Added maximum continuous automatic time calculation
2020.09.17
○Ver3.14
▼ additional functions
・The data of the tool life management function of OSP equipment is reflected in the KOM-MICS “Cutting Tool life monitor” function.
2020.09.08
○Ver3.13
▼ additional functions
・Addition of “Process start” history function (process start data acquisition)
▼ bug fixes
・Fixed a bug that the stop factor is not recorded correctly due to “Stop in a prg” function.